Dan Dulac

6.63K subscribers
30:15
Can I get my DL800 transmission to work?
Dan Dulac
4.5K views • 2 months ago
28:12
Front Bodywork Nearly Done!
Dan Dulac
6.6K views • 2 months ago
19:06
A New Plan for my DL800 DCT Transmission!
Dan Dulac
4.4K views • 5 months ago
50:26
PART-3: I Configure my MoTeC Dash with OEM CAN BUS Data!
Dan Dulac
7.3K views • 7 months ago
43:13
PART-2: More CAN BUS Reverse Engineering on my R8/Huracan Powertrain!
Dan Dulac
10K views • 7 months ago
40:25
PART-1: I Reverse Engineer the OEM CAN BUS on my R8/Huracan Powertrain!
Dan Dulac
41K views • 7 months ago
33:22
Bodywork Bingo!
Dan Dulac
3.4K views • 8 months ago
32:14
Go Kart Mode: ENABLED!
Dan Dulac
4.1K views • 9 months ago
24:59
The V10 Roars to Life Once Again!
Dan Dulac
4.6K views • 10 months ago
30:35
I Try Upholstery for the First Time!
Dan Dulac
3.2K views • 1 year ago
27:06
I Made a Carbon Center Console!
Dan Dulac
8.6K views • 1 year ago
31:06
I Design a Custom 3D Printed Gauge Bezel!
Dan Dulac
4.4K views • 1 year ago
32:14
New Carbon Air-box Lids Finished!
Dan Dulac
4.3K views • 1 year ago
28:59
Rear Body Goes Under the Knife!
Dan Dulac
3.2K views • 1 year ago
33:35
Build Summary Part-1: The First 20 Episodes in 1 video!
Dan Dulac
2.3K views • 1 year ago
15:54
Immobilizer-Free Transmission Mechatronic Installed!
Dan Dulac
3K views • 1 year ago
31:48
She's back from the Tuner!
Dan Dulac
4.3K views • 1 year ago
6:40
First Revs of the V10!!
Dan Dulac
4.9K views • 2 years ago
16:32
We Defeated the Electronic Immobilizer!
Dan Dulac
4K views • 2 years ago
29:13
First start attempt!
Dan Dulac
5.1K views • 2 years ago
32:22
I made an expensive mistake!
Dan Dulac
4.3K views • 2 years ago
26:48
*Major Update* My heat shielded headers are back!
Dan Dulac
6.6K views • 2 years ago
12:13
My V12 Vantage goes on a Lithium diet: I install an AntiGravity LiPo Battery!
Dan Dulac
2.1K views • 2 years ago
21:11
I design a custom speed sensor setup!
Dan Dulac
3.9K views • 2 years ago
23:32
Watch me cut up my Lambo engine wiring harness!
Dan Dulac
3.3K views • 2 years ago
13:24
My 100% Carbon Fiber V10 Intake Systems is Complete!
Dan Dulac
4.2K views • 2 years ago
27:49
Carbon Fiber Skinning Bonanza!
Dan Dulac
4.5K views • 2 years ago
28:00
I made my own 3D-printed Carbon Fiber NACA Ducts!
Dan Dulac
5.8K views • 2 years ago
24:31
I *SOLVED* my Cold Air Intake Dilemma!
Dan Dulac
4.6K views • 2 years ago
26:16
The engine bay is FULL!
Dan Dulac
6.6K views • 2 years ago
Load More