Published On May 1, 2017
This video shows you how to configure Static NAT on Cisco Router using the Packet Tracer software.
✅ S U B S C R I B E ► http://goo.gl/8d0iG9
✅ Article ► https://www.sysnettechsolutions.com/e...
To configure #Static #NAT:
Step 1: If you have not installed #PacketTracer before, please refer to the following videos to install Packet Tracer on Windows, Linux, and macOS.
Windows ➦ • How to Install Cisco Packet Tracer 7....
Linux / Debian ➦ • How to Install Cisco Packet Tracer 7....
macOS ➦ • How to Install Cisco Packet Tracer 7....
Step 2: After installing it, add two Cisco Routers, one Cisco Switch, and two computers to the Packet Tracer workspace.
Step 3: Specify local and WAN IP addresses.
Step 4: Configure the 192.168.1.0/24 network for the local network and the 10.0.0.1/30 network for the WAN.
Step 5: Assign IP addresses to the computers on the local network.
Step 6: Assign IP addresses to the GigabitEthernet interfaces of Router0 and Router1 and turn the ports on.
Step 7: Test the connection by pinging Router1 over PC0 and PC1.
Step 8: Next, configure the interface as follows because the Gig0/1 interface of Router0 is in the IP NAT INSIDE field.
R1# conf t
R1(config)# interface gig0/1
R1(config-if)# ip nat inside
R1(config-if)# exit
R1(config)# interface gig0/0
R1(config-if)# ip nat outside
Step 9: After you have defined the Router's IP NAT regions, execute the following command to configure Static NAT in Router0 global configuration mode.
R1# conf t
R1(config)# ip nat inside source static 192.168.10.10 10.0.0.1
Step 10: If you ping Router1 over PC0, you can see that the network connection is established.
Step 11: Now, ping to Router1 from PC1 and check that PC1 cannot reach Router1.
Step 12: Since we have not configured Static NAT for PC1, PC1 will not be able to reach Router1.
Step 13: Execute the following commands in user mode to verify and control Static NAT.
➦ show ip nat translation
➦ show ip nat statistics
➦ clear ip nat statistics
➦ debug ip nat
Step 14: Don't forget to subscribe to our YouTube channel for more videos on Cisco Networking training with Packet Tracer!
What is Static NAT?
Static NAT creates a fixed translation of real address(es) to mapped address(es). With dynamic NAT and PAT, each host uses a different address or port for each subsequent translation. Because the mapped address is the same for each consecutive connection with static NAT, and a persistent translation rule exists, static NAT allows hosts on the destination network to initiate traffic to a translated host (if an access list exists that allows it).
The main difference between dynamic NAT and a range of addresses for static NAT is that static NAT allows a remote host to initiate a connection to a translated host (if an access list exists that allows it), while dynamic NAT does not. You also need an equal number of mapped addresses as real addresses with static NAT.
──────BEST PRODUCT FOR CISCO TRAINING───────
✅ Buy ► http://bit.ly/CiscoNetworkingDummies
───────────────RELATED VIDEOS───────────────
➊ How to Configure RIP Routing
➦ • How to Configure RIP Version 1 (RIPv1...
➋ How to Configure Static Routing
➦ • How to Configure Static Routing on Ci...
➌ How to Connect Two Networks in Packet Tracer
➦ • How to Connect Two Networks using Cis...
➍ How to Configure RIP Version 2
➦ • How to Configure RIP Version 2 (RIPv2...
➎ How to Configure EIGRP
➦ • How to Configure EIGRP on Cisco Route...
───────────────FOLLOW US───────────────────
✔ Facebook
➦ / sysnettechsolutions
✔ Twitter
➦ / sysnettechs
✔ Pinterest
➦ / sysnettechs
✔ Instagram
➦ / sysnettech_solutions
✔ LinkedIn
➦ / tolqabaqci
███████████████████████████████████████████