Published On May 19, 2023
In this video I'll show you how to test what your klipper controlled 3d printer can do and show you how to set a limit for your acceleration to avoid print defects at higher speeds.
*Since recent firmware change, it is necessary to issue a 'restart' command after changing any settings or following any calibration procedures.*
Ringing Tower stl: https://www.klipper3d.org/prints/ring...
Commands to copy & paste
Zero Pressure advance:
SET_PRESSURE_ADVANCE ADVANCE=0
Acceleration Test (1500mm/s start):
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=1500 STEP_DELTA=500 STEP_HEIGHT=5
Acceleration Test (7500mm/s start):
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=7500 STEP_DELTA=500 STEP_HEIGHT=5
Acceleration Test (6000mm/s start):
TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=6000 STEP_DELTA=500 STEP_HEIGHT=5
Affiliate links (If you purchase something after clicking any of the below links I may earn a small commission at no cost to you. This is a great way to support the channel)
*Creality Sonic Pad*
UK: https://www.geekbuying.com/go/7TPdqKOx
US: https://www.geekbuying.com/go/7TPdvEYU
Everywhere else: https://www.geekbuying.com/go/7TPawLUl
Discount Code: NNNCRESONPAD
Amazon
https://amzn.to/3AiYtwD
Discount code: 10NTDPJE
*Other Sonic Pad Videos*
Sonic Pad Review: • Creality Sonic Pad - The Easy Klipper...
Sonic Pad Basic Series
Part 1 - Connecting to a Creality 3D Printer: • How To Connect A Creality 3D Printer ...
Part 1a - Connecting to a non-Creality 3D Printer: • How To Connect A Non-Creality 3D Prin...
Part 2 - Completing initial setup: • Completing The Initial Setup Of The S...
Part 3 - Starting a print and UI Tour: • Starting A Print With A Sonic Pad And...
Part 4 - Controlling remotely and WEB UI: • How To Control Your Sonic Pad Remotel...
Part 5 - Connecting a camera and tinelapse videos: • How To Connect A Camera To Your Soni...
Sonic Pad Intermediate Series
Part 1 - PID Tune • How To PID Tune With The Sonic Pad - ...
Part 2 - E-Steps/Rotational Distance • How To Tune E-Steps/Rotational Distan...
Part 3 - Slicer Settings • Slicer Settings and Profiles With Cur...
Part 4 - Sending Prints From Slicer/Images On Screen • How to Send Files To Your Sonic Pad A...
Part 5 - Input Shaping - • Tune Input Shaping With The Included ...
Part 6 - Pressure Advance - • Video
Part 7 - MACROs - • Video
Part 8 - Max Acceleration - • Maximum Acceleration Test (How Fast C...
Part 9 - Mid-print Filament Change - • How To Complete a Mid-Print Filament ...
Other
Firmware Update September '23 - • Creality Sonic Pad Firmware Update - ...
Creality Sonic Pad - How To Update Firmware Without Losing Everything! - • Creality Sonic Pad - How To Update Fi...
..............................................................................................................................................................
BUY ME A COFFEE
If you're enjoying my content, why not consider supporting the channel by buying me a coffee?
Even very small amounts are greatly appreciated and re-invested into bringing you better content.
https://www.buymeacoffee.com/rickyimpey
You can also use the YouTube 'Thanks' button above if you prefer.
...............................................................................................................................................................