00:00 Opening

00:21 Cut of frame material
The frame is 2 x 4, and the frame of the top plate is 15 mm x 45 mm.
I used cedar wood.

Tool: HIKOKI FC7FSB Slide circular saw
https://amzn.to/3bH2ks5
Shinwa Complete Square 15cm
Https://amzn.to/3heBtnQ
E-value EVC-200SCL dust collector
https://amzn.to/3c61inR

01:18 Pocket hole processing

Tool: kreg Kreg R3
https://amzn.to/3cbD91e
Kreg PREMIUM FACE CLAMP
https://amzn.to/3iQjl4X
Kreg Pocket Hole Screw-2 "
https://amzn.to/36fabK8
Bosch GBM13RE electric drill
https://amzn.to/36iSHwu

02:59 Frame assembly

Tool: Shinwa Rules Co., Ltd. Flat steel square 50 cm
https://amzn.to/2NGbGur
TAKAGI bar clamp 600 mm
https://amzn.to/3cfQxQ5

05:12 Installation of casters
Later, only two walls will be attached, so the casters will rotate.
Adjust and install so that it will not hit even if it is rolled
did. The used casters are sold out
It was almost the same because it had been done.
Https://amzn.to/3pmu8pD

Tool: Makita MTD-001DSX
Https://amzn.to/2XSq9ov
Kakuri Ratchet Bar Clamp
https://amzn.to/2RKec1D

06:24 Embedding this slide circle
First, place a frame at the position where you want to embed the slide circular saw.
I will put it in. Then use a hand saw to make one of the frames
Cut out the part. Next, temporarily place the top plate and frame
Cut the top plate so that it protrudes 10 mm
Su. Next, create a table on which the circular saw sits and clamp it.
Temporarily fix it with. Put a circular saw on the top plate and
Adjust until it becomes a rat. Adjustment
If possible, fix it with screws.

Tool: Shinwa Rules Aluminum straight scale Alsuke 1m
https://amzn.to/3iR8hUR
Shinwa El Angle Plus 1.2m
Https://amzn.to/3h3QYPk
HIKOKI FC6MA3 Circular saw
Https://amzn.to/2XSXfol
Makita Random Thunder BO5030
https://amzn.to/3qSgHhK
VOLTAGA cordless pin tacker
https://amzn.to/39jHKwh
‥
11:51 Cutting and mounting of wall and shelf boards
The material is 9mm thick softwood plywood

Tool: Shinwa T-slide II
Https://amzn.to/2XI0uA3

12:49 Storage of tools

13:08 Fixing the top plate
The top plate is also fixed in the pocket hole.
It was. The depth of the hole and the width so as not to penetrate the top plate
Adjusting and checking the length of the shoe.

13:57 Painting the top plate
Paint used this time: Asahipen Water-based highly durable two-component urethane varnish transparent https://amzn.to/2YhiaBZ

15:30 Completed

【Photographic Equipment】
◻️ Camera, lens
SONY α7c ILCE-7C
https://amzn.to/3nN3AfC
Tamron 20mm F / 2.8 Di III OSD M1: 2 (Model F050)
https://amzn.to/3nOBOQ5

◻️ Editing software
Lumafusion

◻️ BGM
epidemic sound
Deep and Abiding / Dayon