Published On Jul 3, 2024
Changing the transmission oil and filter in your Ford Endeavour can help smooth out gear shifting and reduce jerks. Here’s a detailed guide on how to do it:
Tools and Materials Needed:
1. **Transmission oil (ATF)**: Check your owner’s manual for the specific type and amount required.
2. **Transmission filter**: Make sure it is the correct one for your Ford Endeavour model.
3. **Transmission oil pan gasket**: If your filter kit doesn't include one.
4. **Ratchet and socket set**: For removing the transmission pan bolts.
5. **Drain pan**: To catch the old transmission fluid.
6. **Funnel**: For adding new transmission fluid.
7. **Torque wrench**: To properly tighten bolts.
8. **Safety gloves and glasses**: For protection.
9. **Jack and jack stands**: To safely lift and secure the vehicle.
Steps to Change Transmission Oil and Filter:
1. **Warm up the engine**: Start your Ford Endeavour and let it run for a few minutes. Warm fluid drains more easily and carries away more contaminants.
2. **Lift the vehicle**: Use a jack to lift the vehicle and place it securely on jack stands.
3. **Locate the transmission pan**: It is usually located under the vehicle, towards the middle.
4. **Drain the transmission fluid**:
- Place the drain pan underneath the transmission pan.
- Remove the transmission pan bolts gradually, allowing the fluid to drain into the pan.
- Carefully remove the pan, making sure not to spill the fluid.
5. **Remove the old filter**:
- The filter will be attached to the transmission body. Remove it carefully.
- Some models may have bolts securing the filter, so use the appropriate socket if needed.
6. **Install the new filter**:
- Attach the new filter in the same position as the old one.
- If the filter has a gasket, ensure it is properly seated.
7. **Clean the transmission pan**:
- Thoroughly clean the inside of the pan with a clean rag or paper towel.
- Remove any debris or sludge.
8. **Replace the transmission pan gasket**:
- If the gasket is reusable and in good condition, you can reuse it. Otherwise, replace it with a new one.
9. **Reattach the transmission pan**:
- Securely bolt the pan back to the transmission body. Use a torque wrench to tighten the bolts to the manufacturer’s specifications to avoid overtightening.
10. **Add new transmission fluid**:
- Lower the vehicle back to the ground.
- Locate the transmission dipstick tube under the hood.
- Using a funnel, pour the new transmission fluid into the tube.
- Check the fluid level using the dipstick and add more if necessary, following the specifications in your owner’s manual.
11. **Check for leaks**:
- Start the engine and let it run for a few minutes.
- Check under the vehicle for any signs of leaking fluid.
12. **Test drive**:
- Take your Ford Endeavour for a short drive to ensure smooth gear shifting and proper transmission operation.
Notes:
- Always use the type of transmission fluid specified in your owner’s manual.
- Properly dispose of the old transmission fluid at a recycling center or auto parts store.
If the problem persists after changing the transmission oil and filter, it may be indicative of a more serious issue that could require professional diagnosis and repair.
#fordendeavour #ford #fordendeavourtransmissionoil #automaintenance #automobile #mechanic #service
• Toyota Corolla Altis AC not cooling d...
• BMW x1 f48 2017 ac cooling coil repla...
• kia carnival suspension problem fix
• Audi A6 MMI Screen problem see Disman...
• Hyundai i10 grand cooling system repl...
• ford endeavour engine problem here is...
• BMW DRIVETRAIN MALFUNCTION FIX BMW F10
• audi a6 petrol filled with diesel ins...
• Video
• Jaguar xjl infotainment system and ac...
• Jeep compass a/c system replace compr...
• skoda Octavia water loss problem how ...
• Toyota fortuner rear disc routers and...