I get a lot of questions about cabinet and carcass construction and in this series I aim to answer them all; in Part 1 I discussed the fundamentals of construction, and here in Part 2 I'm going through the most basic methods of joining the sides to the top & base - but should that be screws, or nails?

Part 1 of this series is here -    • Cabinetry Basics Part 1 [video 435]  

+++++++++

Become a 10minuteworkshop Plus member - more details at 10minuteworkshop.com, sign up directly at 10minuteworkshop.plus

*Support 10 Minute Workshop as a YouTube Member* http://bit.ly/10minuteMember

*Support 10 Minute Workshop on Patreon* -   / 10minuteworkshop  

**Please note that I am moving away from the legacy member platforms to concentrate on my own memberships at 10MinuteWorkshop Plus; member benefits at Patreon and YTM will be significantly reduced from October 2022.

Support the channel directly - http://bit.ly/donate_to_10minuteworkshop

+++++++++

If you’re looking for a few gift ideas and would like to support the channel then take a look at my Etsy store, my Amazon Affiliate store, or any of the links below.

My Etsy - http://bit.ly/10minuteShop

Amazon store - http://bit.ly/10minuteworkshop

My ‘social’ links & contacts in one place - https://www.10minuteworkshop.com/links

Full list of ‘Stuff I use’ at Full list of ‘Stuff I use’ at https://www.10minuteworkshop.com

Connect with me on twitter @10minuteshop

Connect with me on Instagram @10minuteworkshop

+++++++

As an Amazon Associate, I earn from qualifying purchases made through these links.

Wherever possible links are to actual products used, but this is not always possible e.g. some products are not available in the US, so something [similar] has been linked to instead.

Amazon UK - https://www.amazon.co.uk/shop/petermi...

++++++++

Mentioned in this video:-

Peanut 2 connector system - http://shop.intelligentfixings.com?ref=10minuteworkshop

Buttonfix - https://amzn.to/2JIXa35 (US: http://bit.ly/buttonfix_US)

Benchdogs Rail Dogs - http://bit.ly/raildogs

Trend MFT router jig - https://amzn.to/34wSp3b

Benchdogs rail square - https://bit.ly/bench-dogs

Festool TS55 Tracksaw - http://amzn.to/2pGvzDS (US: http://amzn.to/2oOgGhw)

Festool Midi extractor - http://amzn.to/2tCIN3Q (US: http://amzn.to/2rKNIOx)

Bessey Duo Klamp - http://amzn.to/2tsSWQs (US:http://amzn.to/2sVaRBH)

Hultafors Talmeter tape measure - http://amzn.to/2pHwnbH (US: http://amzn.to/2oqLQc9)

Moldex 6810 in-ear defenders - https://amzn.to/2P2c5nP (US:https://amzn.to/2LgIsye)

Mirock square - https://etsy.me/2MC0RT

++++++++

Other useful gear…

Festool MFT - https://amzn.to/2x49HHE (US: https://amzn.to/2J25aKy)

Festool PDC 18/4 - http://amzn.to/2s3J0eq (US: http://amzn.to/2tWUHEL)

Festool Granat abrasive - http://amzn.to/2A3c1vW (US: http://amzn.to/2gPAAUz)

Festool RTS 400 - http://amzn.to/2x6zGZW (US: http://amzn.to/2i84yXn)

Spax screws - http://amzn.to/2oYWydc (US: http://amzn.to/2oOjkDT)

Festool ETS 150/5 - http://amzn.to/2sapsq9 (US: http://amzn.to/2ssbZgq)

Festool CTL Sys - http://amzn.to/2sKa2t3 (US: http://amzn.to/2tCvVdZ)

Festool CTL SYS Bags - https://amzn.to/2G9eFVd (US: https://amzn.to/2GduBpo)

Trend Air Stealth Facemask - https://amzn.to/2zah0P6 (US: https://amzn.to/2T5ww6X)

Bahco 6” combi square - http://amzn.to/2oumhX4 (US: http://amzn.to/2ouSg9k)

Silicone brush set - http://amzn.to/2guo6Sm (US: http://amzn.to/2yEWbZI)

Silicone brush (single) - http://amzn.to/2l5rNTD (US: http://amzn.to/2zqFaQl)

Polyvine PolyTen PVA - http://amzn.to/2svT03N (US: http://amzn.to/2rmHYL3)