Published On Nov 12, 2018
Did our video help you? If so, consider buying us a beer: https://bit.ly/3feE6tJ
*PLEASE READ THIS AND THE COMMENT WE PINNED FOR HELPFUL INFORMATION*
In this video we show you how to replace the upper balljoints on a 3rd Gen Toyota 4runner. This would also be the same steps to replace the upper balljoints on a 1st Gen Toyota Tacoma since the front suspension on those two vehicles are the same.
*TORQUE VALUES*
Upper Balljoint Castle Nut - 80 ft-lbf
Lower Balljoint Castle Nut - 105 ft-lbf
Outer Tie Rod Castle Nut - 67 ft-lbf
Brake Caliper Bolts - 90 ft-lbf
CV Axle Nut - 174 ft-lbf
Wheel Lug Nuts - 85 ft-lbf
*PARTS*
*Upper Balljoint - #43310-39016
https://amzn.to/2ssyLpK
*Upper Balljoint Reboot Kit - #43324-39015
https://www.toyotapartsdeal.com/oem/t...
*HELPFUL TOOLS*
If you're looking for other tools not used in this video, check out Timmy's Master Tool List.
https://www.amazon.com/shop/timmythet...
*6 Ton Jack Stands
https://amzn.to/2MM91w6
*Heavy Duty Rubber Wheel Chock
https://amzn.to/3lNC3MG
*Long Magnetic Parts/Tool Tray
https://amzn.to/2m89y0D
*Medium Size Magnetic Parts/Tool Tray
https://amzn.to/2ky8Qt8
*Small Size Magnetic Parts/Tool Tray
https://amzn.to/2m6kQ5y
*Milwaukee Mi12 Cordless Ratchet
https://amzn.to/2utRZsE
*Milwaukee M12 Battery
https://amzn.to/3FJZO1j
*Milwaukee M12 High Capacity Battery
https://amzn.to/2HEFTpu
*Milwaukee M12 Battery Charger
https://amzn.to/2uo2o9x
*3/8” Drive Regular Extension Set
https://amzn.to/2OehCao
*3/8" Drive 6 Point Metric Standard Socket Set
https://amzn.to/32WIh0M
*Straight Needle Nose Pliers - (used to remove cotter pins and install new ones)
https://amzn.to/2pQ6yIa
*20 Piece Screwdriver Set - (nice complete set)
https://amzn.to/34aLrQ1
*1/4" and 3/8" Flex Head Ratchet Set - (used the 3/8" ratchet in this video. These ratchets are super functional and will make your wrenching life easier)
https://amzn.to/2ql8nNA
*1/2" Drive Flex Head Gear Wrench Ratchet - (used for the bigger fasteners)
https://amzn.to/2Wnbq2r
*1/2" Drive Deep Metric Impact Socket Set
https://amzn.to/3wdRVhq
*1/2" Drive Shallow Impact Socket Set
https://amzn.to/2pCrdPQ
*Brake Caliper Hanger Hooks - (much better than using bailing wire)
https://amzn.to/31JGsUA
*Plastic Mallet - (to break free rotor from hub face)
https://amzn.to/2CCOqVP
*Rotary Hammer Chisel Set - (slim chisels to help get axle nut hub cover off)
https://amzn.to/2OmiMCe
*Chisel & Punch Set - (used chisels from this kit to get hub cover off)
https://amzn.to/37Fwdor
*Mayhew 5 Piece Prybar Set - (used small prybar to pop off hub cover)
https://amzn.to/2Ob8THw
*Knipex Diagonal Cutters - (to remove cotter pins and cut them to size)
https://amzn.to/300BRRE
*Dewalt 1/2" Drive Impact Gun - (to remove lug nuts and several other fasteners for this job)
https://amzn.to/2M2Y9J1
*Dewalt 3/8" Impact Gun - (used for UBJ castle nut)
https://amzn.to/2uqWnZy
*Dewalt Batteries
https://amzn.to/2urcx59
*Dewalt Battery Charger
https://amzn.to/2Ud8RlY
*Large Metric Impact Socket Set (29mm-38mm) - (has 35mm socket for axle nut)
https://amzn.to/2qdhWhG
*OTC Front End Service Kit - (has pullers used for this job)
https://amzn.to/2LuisQc
*3/8” Drive Shallow Impact Socket Set
https://amzn.to/2KnoYaq
*Yost Bench Vice - (Vice I used for this job)
https://amzn.to/2ofa4LD
*Yost 6” Aluminum Vice Jaw Caps - (to protect the parts your clamping)
https://amzn.to/2PopCrd
*Snap Ring Pliers - (used to remove balljoint snap ring)
https://amzn.to/2ZZyZEB
*Emery Cloth Roll - (to clean up steering knuckle)
https://amzn.to/38axDYh
*Anti-Sieze - (used on face off hub)
https://amzn.to/2XZbpnu
*CDI 1/2" Drive 30-250 Foot Pound Torque Wrench
https://amzn.to/2UPhyjK
*CDI 3/8" Drive 10-100 Foot Pound Torque Wrench
https://amzn.to/2U2vUA4
*Cotter Pin Set
https://amzn.to/2OoD38K
*Brake Cleaner - (to clean up rotors)
https://amzn.to/2KuJ6Yw
*Mini Grease Gun - (used to lubricate ABS sensor o-ring)
https://amzn.to/2KKDXf2
*Red Devil All Purpose Grease - (grease for gun)
https://amzn.to/2O9DXY3
*Balljoint Presss and Associated Adapters
*OTC-7249 Ball Joint Service Set
https://amzn.to/2I1PlEm
*I bought all the special adapters from Coastal Tool Supply https://www.coastaltoolsupply.com/
*Part Numbers and What I Paid:
OTC-538591 Adapter, Removing $20.89
OTC-38354 Receiving Cup $24.38
OTC-314392 Plug $9.55
OTC-38355A Installing Cup $25.25
OTC-313968 Remover $10.43
Shipping: Standard Shipping: $8.85
Total: $203.80
**PDF on how to assemble all the adapters with the c-press to get the job done. https://www.otctools.com/sites/defaul...
**As Ebay Partner Network members, we earn commissions from qualifying purchases.
**As Amazon Associates we earn from qualifying purchases.